PRx Profile PRO Folding Squat Rack vs Rogue HR-2 Half Rack

PRx Profile PRO Folding Squat Rack versus Rogue HR-2 Half Rack is a spec comparison, not a test. Fold-away versus a half rack. Every number below is copied from a manufacturer page or official sheet and carries an as-of date of 2026-10-14 on the product records. If a field is blank on the maker’s page, it stays blank here.

PRx describes the PRx Profile PRO Folding Squat Rack as: Folds to 4 in from the wall; 89 in uprights want a 107 in recommended ceiling. PRx lists 11-gauge 3x3 steel uprights in 81, 89, or 95 in heights, 53 in total width, 48 in outside-of-uprights width, 5/8 in holes, 2 in front spacing with 1 in in the bench area, and a 1,000 lb capacity. Pull-up bars are 42 in long and 1.25 in diameter. The rack folds to 4 in from the wall. Squat racks carry a limited lifetime warranty on structural welds, frames, and hardware.

Rogue describes the Rogue HR-2 Half Rack as: 17 in rear inside depth on a 48 in x 49 in flat-foot footprint that does not need to be bolted down. The HR-2 uses 3x3 in 11-gauge uprights and a 2x3 in 11-gauge base, matching the SML-2’s 48 in x 49 in footprint, plus 17 in rear crossmembers. Gear specs list 49 in length, 48 in width, 92.25 in or 110.25 in height, and 225–255 lb depending on uprights. Front uprights are 90 in or 108 in; rear uprights are 70 in or 90 in. A Monster Lite J-cup pair and 43 in single skinny pull-up bar are included.

On listed height, PRx Profile PRO Folding Squat Rack is 89 in and Rogue HR-2 Half Rack is 92.25 in. Width is 53 in versus 48 in. Depth / length is not published in versus 49 in (falling back to a listed length where a maker omits depth). Unit weight is not published lb versus 225 lb. Listed load or user capacity is 1000 lb versus not published lb.

Uprights are listed as 3x3 (11 gauge) versus 3x3 (11 gauge). Hole spacing is “Front 2 inch (1 inch in bench area); side 2 inch” versus “Westside hole spacing”. Inside depth is not published in versus 17 in. A 30 in interior changes which benches fit; a 43 in interior is a different machine. Pull-up bar height is not published in versus not published in. Warranty text is “Limited Lifetime Warranty on PRx squat rack frames, welds, and installation hardware” versus “not published”.

FitScout spec scores — our weighted rubric, not Amazon stars — are 73 for PRx Profile PRO Folding Squat Rack and 69 for Rogue HR-2 Half Rack. Missing fields do not count as zeros; they drop out of the average. The rubric for power racks is published on the methodology page.

We do not print manufacturer list prices or Amazon prices on this page. Use Check price on each card for the current offer.

Who the PRx Profile PRO Folding Squat Rack is for, in our reading of the spec sheet: Shared garages or rooms that need a wall-mounted 3x3 folding rack with a 1,000 lb capacity. Skip it when Spaces without wood studs at 16 in or 24 in on center and no ledger board, or ceilings below the listed minimum for the chosen height.

Who the Rogue HR-2 Half Rack is for: Lifters who want a Monster Lite half rack with plate storage behind the lift and a 43 in skinny pull-up bar. Skip it when needs a full cage depth for squatting inside the posts — the listed rear inside depth is 17 in.

If ceiling height is the constraint, prefer the shorter published frame and then run Will-It-Fit with your ceiling, your height, and the exercise. HAJEX’s standing-press rule of thumb is height × 1.33 plus about 9 in for full-size plates. A rack that “fits the room” on assembled height can still fail a pull-up if there is not about a foot above the bar.

This page does not say either product was used, assembled, or worn-in by FitScout. Sources are the manufacturer URLs on each spec row. If a maker updates a dimension after 2026-10-14, the as-of date is the tell.

704 words. Spec-based analysis, not a test report.